I was really excited when I installed my new LED strip lights. They looked so sleek and modern, and they were a huge improvement over the old fluorescent light fixtures that were in my kitchen.<\/p>\n\n\n\n
But about six months after installing them, I noticed that half of the lights had stopped working. I wasn’t sure what to do, so I did some research online. After reading a few articles and forums, I think I have a pretty good idea of what might have gone wrong.<\/p>\n\n\n\n
In this article, we will explore some of the possible reasons why your LED strip lights might have stopped working.<\/p>\n\n\n\n
Here are some of the major reasons why half of your led strip lights might have stopped working;<\/strong><\/p>\n\n\n\n Let’s take a closer look at each of these reasons.<\/p>\n\n\n\n One possible reason why your LED strip lights might have stopped working is insufficient heat sinking.<\/p>\n\n\n\n This means that the heat from the LEDs is not being dissipated efficiently, and as a result, the lights are burning out causing parts or half of the led strip light to stop working.<\/p>\n\n\n\n There are several things you can do to improve heat sinking on your LED strip lights. One is to use a better thermal adhesive or paste between the LED Strip and Heatsink.<\/p>\n\n\n\n Another is to make sure that there is good contact between the LED Strip and Heatsink. You can do this by using a clamp or compression screw.<\/p>\n\n\n\n Finally, you can also try increasing the airflow around the LED strip lights. This will help to dissipate the heat more efficiently.<\/p>\n\n\n\n If your LED strip lights are not getting enough heat sinking, then this is likely to be the cause of why half of it have stopped working.<\/p>\n\n\n\n Another possible reason why half of your LED strip lights might have stopped working is voltage.<\/p>\n\n\n\n This means that the voltage being supplied to the LED Strip Lights is too high or too low, and as a result, the LEDs are burning out.<\/p>\n\n\n\n You can check the voltage rating of your LED Strip Lights by looking on the product packaging or on the manufacturer’s website.<\/p>\n\n\n\n If you are not sure what voltage your LED Strip Lights need, then it is best to consult with the manufacturer or an electrician.<\/p>\n\n\n\n It is important to note that if you are using a transformer, then you must use one that is specifically designed for LED strip lights. Using the wrong transformer can cause parts of the LED Strip Lights to overheat or fail.<\/p>\n\n\n\n If the voltage is not the problem, then it is likely that this is the reason why half of your LED strip lights have stopped working.<\/p>\n\n\n\n Another possible reason why your LED strip lights might have stopped working is an improper connection<\/a> after cutting and joining the led strip light.<\/p>\n\n\n\n This means that when you cut the LED strip light, you did not properly connect the two ends together. As a result, some of the LEDs are no longer receiving power and they have stopped working.<\/p>\n\n\n\n To avoid this, it is important to make sure that the two ends are properly connected together. You can do this by using a solder iron and solder, or you can use special connector pins.<\/a><\/p>\n\n\n\n If the connection is not the problem, then it is likely that this is why half of your LED strip lights have stopped working.<\/p>\n\n\n\n Another possible reason why half of your LED strip lights might have stopped working is water damage.<\/p>\n\n\n\n This means that either the LEDs or the circuitry has been damaged by water. While some led strip lights are waterproof and water-resistant, not all of them are.<\/p>\n\n\n\n If you have noticed that your LED strip lights have stopped working after being in contact with water, then it is likely that they have been damaged by water.<\/p>\n\n\n\n You can try drying the LED strip lights out by using a hairdryer on low heat. However, if the LEDs or circuitry has been damaged by water, then they will likely need to be replaced.<\/p>\n\n\n\n So check if your led strip lights are waterproof or water-resistant. If they are not, then this is likely to be the reason why half of them have stopped working.<\/p>\n\n\n\n Another reason I found to cause half of the LED strip lights to stopped working is a manufacturing defect.<\/p>\n\n\n\n This means that there was a problem with the way the LED Strip Lights were manufactured, and as a result, some of the LEDs have stopped working.<\/p>\n\n\n\n If you think that this might be the case, then you can try contacting the manufacturer and requesting a replacement.<\/p>\n\n\n\n You would want to prove that the defect was not caused by your own mishandling of the product.<\/p>\n\n\n\n1. Insufficient Heat Sinking<\/strong><\/h2>\n\n\n\n
2. Voltage<\/strong><\/h2>\n\n\n\n
3. Improper Connection After Cutting The LED Strip Light<\/strong><\/h2>\n\n\n\n
4. Water Damage<\/strong><\/h2>\n\n\n\n
5. Manufacturing Defect<\/strong><\/h2>\n\n\n\n